DIY Paracord Nametape Bracelet

I made myself a paracord nametape bracelet.

I've had a lot of people ask me about it, so I thought maybe it would be cool to show how I did it. Yeah, it's a little cheesy. That's okay with me. Maybe when I'm living near base and I'm a more sophisticated Army wife, I won't wear such things. Maybe. But for now, I'm living in an area with hardly any other MilSOs (I've looked) and I'm proud to wear this.

This one that I'm showing for the tutorial says "U.S. Army." The one I wear actually does say his/our last name. I think it's a bit more affectionate that way. But since I'm trying to remain a bit anonymous here, I made a U.S. Army one especially for this tutorial. And I think this one is pretty cool too.
Things you need:

  • Nametape
  • Paracord. You can get all different colors on amazon. And you think you won't need 100 feet, but you can pretty much use this stuff for anything. Otherwise, you can get it by the foot at most military surplus stores.
  • A cute button. I got mine at Cupid's Cottage on Etsy. If you are interested in really cool paracord bracelets (minus the nametape) check out her store. 
  • 1/4 inch eyelets. The ones I got are a kind of bronze color that I thought looked nice with the green. Got them at walmart. 
  • Pliers
  • Matching thread
  • Matches/lighter
  • Hammer
  • Exacto knife
  • Pen (not shown in pic because I forgot) 
So start with your nametape. 

I got my nametape off of some old uniforms that my husband's family were using for paintballing. I have no idea how old this is, but I kind of like that it looks a little worn. So since I just seam-ripped it off a uniform, it was already nicely ready for a bracelet with the folds on the side. You may have to iron it so it looks like this:
If you want to put a couple stitches in it so it stays, that wouldn't hurt. I didn't on mine. The eyelets will do a pretty good job holding the folds in place.
Next, make a mark where you are going to place the eyelet. Then, very carefully, start to make a hole with the Exacto knife.
Seriously. Be careful.
This is what happens if you aren't careful. A trip to the ER and a scar. 
Making the hole for the eyelet is the most annoying part. I also use a pen to round off the hole and make sure the eyelet would fit.
There is a more correct way to place an eyelet. I kind of just used the pliers and a hammer because I don't own an eyelet tool. Here is a good tutorial on how to do it correctly.
This is what it should look like after placing the eyelets. 
Next, use the tread to tie the button to the eyelet. It might go faster to loop it around a bunch if you use a needle. I used about 2 feet of thread so it was looped around a lot. Yes, you could just stitch the button directly to the nametape. That works fine too. I liked the symmetry of having two eyelets so that's why I did it this way. I also stitched it into the nametape a couple times toward the end to secure it. 
You can also see how the eyelet is not placed very well, but no one will ever see the back when I wear it. 
Next, measure a loop of paracord to finish off the bracelet. It's going to be different for everyone, depending on the length of your nametape and your wrist size. I used about 4 inches here. 
 Remove the insides of the paracord. This is optional. It makes the bracelet here a little less-fat.
 Hold the ends of the paracord together with the pliers. If you can, twist one end and stick it slightly inside the other end (remember it's hollow) and burn the ends together. Make sure you have it looped through the eyelet of the bracelet as shown. The idea here is to make a loop without knots. It's hard to hold the ends together with pliers and strike a match so you may either want to hire a friend to help, or you may have better luck with a lighter.
It's also hard to take a picture at the same time. 
Measure one more time to make sure it fits your wrist and goes around the button. Then move your burned part down as shown below. It's going to get covered up. 
Start your square knot. If you are unfamiliar with paracord bracelet/macrame knots, there is a really good tutorial here. Make sure the loop on top has enough room to go around the button. 
Now, depending again on how long the nametape is, you might now have very much room here. I had a little more room on my actual nametape because our last name is shorter than "U.S. Army." 
US Army on the left, the one with his/our last name is on the right. 
So I couldn't tell you exactly how much paracord you would need here, but I think it's safe to say you'll definitely need less than 2 feet for this part. Next, cut off the ends.
I know, it looks bad. Bear with me. 
Hold the ends together with pliers on the back of the bracelet. Then, while holding it with the pliers, burn those two ends together.
This is what it will look like when you are done. 
You could stitch this part too. I kind of like playing with matches and burning things, so I did it this way. Just be really careful.

And that's it! You're done!

And now you have a cute paracord nametape bracelet.

I'm going to help my friend Sam make a Navy one. She ordered a button that says "I love my sailor" from the Cupid's Cottage Etsy shop. Since the Navy nametapes are blue, I think it would be super cute with blue paracord. Have fun! 

<3 Amy

PS: Let me know if I wasn't clear about something. This is only like my second tutorial ever. 


  1. Cute!! And very creative :)

  2. Ooh! I want! And I just so happen to have an extra nametape laying around. The only part about this that intimidates me is the knot tying. I think I could do everything else and then get stuck on that part and never finish.*

  3. where did you find that button????

    1. I linked to the etsy shop that I got it from in the post already.

    2. oh okay sorry.. lol thanks(:

  4. It’s super site, I was looking for something like thisParacord

  5. Just a thought, it would be cool to have two lengths of paracord through both grommets and have your weave continue behind the name tape. That way you actually have a fully functional survival bracelet.

  6. Enter your shipping address here so I can send you this discreet knife for free!

    We’ve have just 75 to give away!

    Just enter your address here so we can send you a free USMC NECK KNIFE™

    What is it?

    This tactical self-defense tool puts confidence around your neck, knowing you have the safety of a purpose-made instrument at your fingertips.

    If you’re going to carry any item as your daily, it needs to be the NECK KNIFE™.


  7. I’m in my bed, you’re in yours. One of us is obviously in the wrong place. Hey, i am looking for an online sexual partner ;) Click on my boobs if you are interested (. )( .)


Post a Comment

Popular posts from this blog

Communication During Ranger School: A Recap

I've Been Doing It Wrong..

MilSO Care Package: Deployment Survival Kit